MP5 5 Pin Euro Key & Thumbturn Cylinder
Code: EK3535-MP5-SCP
The MP5 5 Pin Euro Key & Thumbturn Cylinder is a 70mm or 80mm 5 pin euro profile cylinder with thumbturn and 3 keys.
Read More
If you have a fire door, you will need fire door ironmongery. Specifying the right ironmongery and door hardware is crucial to ensure that the fire rating of a door is maintained and, for the safety of the building’s occupants. The ironmongery in this section of the website is specifically for use on fire doors; the products are CE Marked and Certifire approved and comply with relevant British Standards.
BS EN 1634 Standard
BS EN 1634 is a European fire test standard for all fire door CE Marked ironmongery products. Anything CE marked must also Fire Doors in the UK are typically tested with just three fire rated products: 3 hinges, a door closer and a lock or latch. The bolt in a lock is wired back so that this does not contribute to holding the door closed. This then allows for the door manufacturer to be able to test two key points at the same time:
A fire door must prove that it can withstand a fire attack for a specified amount of time, in order to successfully achieve its fire rating. This means that hot gasses and flames are not to pass through for the duration of a fire test. E.g. FD30 doors should have a 30 minute fire resistance and are tested for 36 minutes, FD60 Doors should have a 60 minute fire resistance and are tested for 67 minutes. This is known as Fire Door Integrity.
Fire Door Integrity does not include the passage of smoke and at the beginning of a fire test, smoke is pushed through the gaps between the door and frame and the meeting styles on a pair of double doors. Any intumescent that is fitted to these doors then expands and fills the gaps to reduce the passage of smoke through the door to 0 until the end of the expected fire rating where the door warps and burns completely.
Fire Rated Hinges
Fire doors should be fitted with 3no. 102mm hinges that are CE marked under Fire Regulations. Fitting 3 hinges will also help stop the door from warping – for extra tall doors over 2200mm, four hinges may be used to prevent this. Occasionally 2 hinges may be used but only with supporting fire test evidence. Fire door hinges must remain attached to the door during a fire test, even if the timber around them is charred. Some steel and Brass hinges are acceptable for use on FD30 30-minute fire doors whilst only steel hinges should be use on FD60 60-minute fire doors. Under BS EN1935:2002, any hinges fitted to a fire door, must be able to achieve the appropriate fire rating. They must also not impede any door closers that may be fitted to the doors and overcome any seals and resistance from latches. Intumescent hinge pads should be used with all hinges on fire doors, even if they are CE Marked, or full compliance with fire ratings.
Fire Rated Door Closers
All door closers fitted to a fire door, whether concealed or overhead, must be CE Marked and suitable for the fire rating of a door. You must not install any ironmongery that has a fire test rating lower than that of the door. For example, if you have a 60-minute fire rated door, you cannot install anything that has a lower fire rating like products with a 30-minute fire rating. You can, however, install a 60-minute fire rated product on a 30-minute fire rated door.
Door Closers should be performance tested to EN1534 and Fire Tested to EN1634 in order to be CE marked. They should also be a minimum of a power size 3 (EN3) when fitted to a fire door.
If a door is to be held open, then an electromagnetic door closer linked up to the fire alarm interface should be used.
Digital Locks
There is no performance test to which Digital Locks should comply, however fire rated digital locks should be supplied with appropriate intumescent and be fire tested to EN 1634 and EN 476.
Locks & Latches Locks
Any lock or latch installed on a fire door must be CE Marked and tested to BS EN 12209. Fire Rated mortice locks and latches can be installed with intumescent jackets and any cut made into the door to accommodate them must be minimal.
Fire Rated Intumescent
Intumescent Seals have an important job of expanding to fill gaps around the edge of the doors to prevent the spread of smoke and fire. It contributes to the fire rating of a door as it slows down the ability of flames to pass through the door. When a fire door and seals are fitted correctly, any gaps around the top and sides should be less than 4mm thick – the seals will expand to fill these in the event of a fire.
Any hinges and morticed locks and latches should be installed with appropriate intumescent sheets or pads. These act as a barrier between the product and the door to ensure that heat transfer is delayed. Always check the fire test certificates to ensure full compliance with any given fire rating.
Fire Rated Accessories & Signage
Accessories on Fire Doors must not affect the integrity of a fire door. There are products like door viewers for example, that have been fire tested with intumescent that are appropriate for use on such doors.
Signage for fire door is mandatory and falls under BS 5499-5:2002 Approved Document B. All fire doors must display signs that either read “Fire Door Keep Locked” or “Fire Door Keep Shut” depending on the function of the door. There are no performance standards for signage, and they should be face fixed to the fire door.
Fire Rated Lever Handles
Fire Rated lever handles should conform to BS EN1906 – the British Standard for Door Furniture. This standard covers all door furniture with backplates or roses. There does not necessarily need to be a CE marking but the handle set should have been put through fire testing and given a Grade 3 for durability and a Grade 1 for Fire Rating.
Fire Rated Pull Handles
Pull Handles, although are never CE Marked, should be tested under BS 476, which is the British fire test standard on building materials and building structures. BS EN476 grades the level of resistance that an ironmongery product has, using a class system. During this test, products are set alight with a pilot flame and then extinguished after 1 minute. The material of the product might start to burn and the test ends when either the flame front reaches a 825mm reference point or after 10 minutes – whichever comes first. The flame is then classified according to the time that the flame crosses certain reference points, the extent of flame spread during the first 1.5minutes of the test, the maximum distance the flame spread (10 minute/825mm limit) and the time taken for the flame to spread.
Intumescent Letterboxes
If you must install a letterbox on a fire door, you must only use an intumescent letterbox so as not to affect the integrity of the fire door.
Categories
Price
Code: EK3535-MP5-SCP
The MP5 5 Pin Euro Key & Thumbturn Cylinder is a 70mm or 80mm 5 pin euro profile cylinder with thumbturn and 3 keys.
Code: XB8465XX
This is an intumescent lock jacket to suit DIN standard mortice locks, made of black graphite. Select 60mm or 80mm backset.
Code: FC20469SS
The ARRONE AR961/69D Stainless Steel Disabled Turn & Indicator grade 304 stainless steel bathroom turn, complements the AR961 lever on round rose door furniture. It has a 52mm diameter with 38mm fixing centres and it is supplied with a 5mm spindle and wood screws.
Code: XB8490XX
These 1mm Interdens intumescent hinge pads are for use with the Royde and Tucker H102 and H208 hi-load hinges. 2no pads are required per hinge.
Code: DLH525
The ARRONE AR525 & AR526 Fire Rated Mechanical Digital Locks are robust push-button mechanical digital locks suitable for internal and external applications.
Code: LB0196SS
ARRONE AR8101 Upright Latch DIN euro profile with a 60mm backset.
Code: FG2010PB
The ARRONE AR461/10 Polished Brass Lever On Round Rose PVD brass safety lever on a sprung round rose with 19mm diameter handle.
Code: HB1598SS
The ZOO VHP243 is a Grade 14, high performance stainless steel hinge.
Hinges are sold as singles, not pairs, complete with fixings.
Code: DCB121SCE
The Briton 121 CE EN 3 Door Closer is a fixed power size EN3 door closer. It is a low duty, low budget door closer in a silver finish.
Code: IB2117SA
These Applique Surface Drop Down Acoustic Door Seals are surface mountable and acoustically tested achieving up to 37dB Rw. They are suitable for use on FD60 (60 minute) timber fire doors.
Code: DCH3500SE
The ARRONE AR3500 EN2-4 Overhead Door Closer is dual handed and suitable for universal door applications. This overhead closer has backcheck, delayed action plus adjustable closing and latching speed.
Code: HB1588SS
The Eurospec HIN1433SEC Stainless Steel Ball Bearing Security Hinges are supplied as singles, complete with fixings. Select from square or radiused corners.
Code: XB8468XX
Easy to fit Codelocks Intumescent Fire Kit to fit with Codelocks mechanical and electronic latch lock products. When fitted they can be installed on 30 or 60 minute fire doors.
Code: LB0146SS
ARRONE AR8103 Bathroom Lock has a 60mm backset and 78mm DIN standard centres. This bathroom lockcase is pierced to accept bolt through furniture.
Code: LB0136SS
ARRONE AR8102 Deadlock is a DIN standard deadlock case that is pierced to accept a euro profile cylinder, and has a 60mm backset.
Code: LB1876SC
The ARRONE AR7004 Euro Profile Mortice Sashlock Case is a euro profile mortice sashlock case, complete with bolt through fixing holes and a brass deadbolt. It is suitable for sprung and most unsprung door furniture.
Code: XB7010WE
This Intumescent Fire Seal - 1050mm length expands when it comes into contact with fire to fill the gap between the door perimeter and the door frame. It is an essential product to maintain a fire door rating and for the safety of a building's occupants.
Sold in packs of 25no lengths. Priced as single lengths.
Code: LB4946SS
The ARRONE AR8023 Mortice Bathroom Lock Case has a 5mm bathroom turn spindle follower, bolt through fixing holes and a brass deadbolt. It has a 67mm or 80mm case size and is suitable for sprung and most unsprung door furniture.
Code: HB3002SS
The Royde & Tucker H131-100 Double Action Door Pivot Hinge Set is a door pivot which allows doors to open in both directions.
Code: IBA730
The Applic drop down seal is available in a variety of lengths. It is surface mounted, with a maximum drop of 15mm, and is fire tested to 60 minutes.
Code: FC31609SS
The ARRONE AR361/11 19mm diameter Lever Latch Door Handle on Backplate is a 19mm diameter satin stainless steel lever latch backplate furniture. This product is supplied with wood screws.
Code: FC31607SS
The ARRONE AR361/13 Stainless Steel Euro Lever Lock Handle on Backplate is a 19mm diameter satin stainless steel euro lever lock backplate furniture. This product is supplied with wood screws and bolt through fixings. It has 47.6mm centres.
Code: FC4000SS
A ZOO ZPS030 Grade 304 Stainless Steel Sprung Door Lever Latch Handle on Round Rose satin stainless steel safety lever latch handle on a sprung round rose.
Code: HB18102SS
The Eurospec H2N14 is a heavy duty Grade 13 stainless steel parliament hinge. Sold as singles. Select the size and finish you need from the below menus.
Code: XB8467XX
A selection of Intumescent Kits to suit various British Standard sashlocks and deadlocks. (Lockcase not included).
Code: XB8121BL
These Corner Acoustic Perimeter Seals dramatically improves the effectiveness of a doorset assembly by reducing noise, smoke and air movement between the gap between the door perimeter and the door frame. These acoustic seals are fully compliant with Approved Document E and are super easy to fit.
Code: HB1568EB
The Eurospec HIN1433 Grade 13 Plated Ball Bearing Hinge is an electro-plated brass finish ball bearing butt hinge measuring 102mm x 76mm . CE marked.
Hinges are sold as singles, not pairs, complete with fixings.
Code: KITLKBD13
This Fire Rated Door Lock and Door Handle Set - Escape Lock Kit includes an escape sashlock for easy egress from the inside and locking ability from the outside. Choose from a basic, high or high-antimicrobial specification level.
Code: NB2402PA
A 75mm diameter Fire Door Keep Locked Sign in satin anodised aluminium.
Code: XB8469XX
Easy to fit Perko-Powermatic Intumescent Kit for use with the Samuel Heath Powermatic door closer, the R100 Perko-Powermatic.
Code: XB8478XX
The Abloy INPK-DIN-65 intumescent lock jacket is designed for use with the EL560 solenoid lock when installed on FD60 rated timber fire doors.
Code: XB8479XX
This intumescent kit for the Abloy EA280 concealed door loop should be installed on timber fire doors to achieve an FD30 or FD60 fire rating.
Code: XB8460XX
A high performance intumescent graphite sheet, ideal to for cutting to size to install with ironmongery on fire rated doors, such as hinges, lockcases, latches and concealed door closers.
Code: PB2050SA
Intumescent Letterbox Assemblies with a 30 minute fire rating - available in a variety of finishes.
Code: NB1931XX
A Push Bar To Open sign with white text and tick symbol on a green background. For installation with panic exit hardware on final exit doors.
Code: XB8440XX/SA
These 1mm self adhesive Interdens intumescent hinge pads are for use with 100mm / 4" fire door hinges. 2no pads are required per hinge.
Code: HB1569SS
The Eurospec Enduro CEN1443 Grade 13 Stainless Steel Broad Butt Hinge is manufactured from marine grade 316 stainless steel.
Code: KITLKBA13
This Fire Rated Door Lock and Door Handle Set - Sashlock Kit is available as a basic specification, high specification or high specification anti-microbial kit. This kit has been put together to make ordering for easier with a one kit per door ironmongery solution.
Code: KITIKBC10
This Fire Door Ironmongery Kit for Corridor - Non-Locking is a single kit solution for corridor doors. Simply select the specification level you require for easy ironmongery specification.
Code: DLB5401
The Borg BL5401 & BL5701 ECP Easicode Pro Digital Locks come with lever handle operation and are a good access control solution for medium to heavy duty doors.
Code: FC4300SS
A pair of Eurospec CSL1194 Grade 304 Stainless Steel T-Bar Door Lever Handle on Round Rose. These stainless steel door handles are available in a polished or satin stainless steel finish.
Code: VB1091SCA
A 250mm x 140mm or 340mm x 340mm, Silver Louvre Vent Face Plate to suit an Intumescent Grille.
Code: XB8900XX
An intumescent pack for use with the AL900 Fire Rated Electric Strike.
Code: FB4001SA
A pair of ZOO ZAA030SA Aluminium Safety Door Lever Handle on Round Rose return to door design lever handles on a screw on round rose. Satin anodised aluminium finish.
Code: KITIKBG13
This Fire Door Ironmongery Kit for Storeroom - Locking is a complete solution for lockable storerooms. Choose from three levels of specification and the option of fire rated or non-fire rated to suit your project, with the flexibility of supplying your own cylinder.
Code: FC4400SS
A pair of Eurospec SW4123 19mm Diameter Grade 316 Stainless Steel Safety Door Lever Handle on Rose return to door design lever handles on a sprung round rose. Unlike many lever handles, these are tested to EN1906 Grade 4.
Code: NB2403PA
A 75mm diameter Automatic Fire Door Keep Clear Sign in satin anodised aluminium.
Code: NB1411XX
A rectangular Fire Exit Keep Clear Vinyl Sign 150mm x 450mm with a running person pictogram and white text on a green/blue background.
Code: FC9000SS
A pair of HOPPE SECUSAN Paris Stainless Steel Door Lever Handles on round rose in the HOPPE SecuSan antibacterial, antimicrobial finish.
Code: HB1488SS-316
This Royde & Tucker H208 Grade 316 Stainless Steel Hinge is a hi-load concealed bearing, marine grade 316 stainless steel butt hinge with fixings.
Hinges are sold as singles, not pairs.
Code: FC31602SS
The ARRONE AR361/12 19mm diameter Stainless Steel Lever Lock Handle on Backplate is a 19mm diameter satin stainless steel lever lock backplate furniture with 57mm centres. This product is supplied with wood screws and bolt through fixings.
Code: XB60DIN
This is an intumescent lock jacket to suit DIN standard lockcases, made of 1mm mono ammonium phosphate. Select 60mm or 80mm backset.
Lockcases are supplied separately.
Code: KITES1FR
A 12V/24V DC ES1 Fire Rated Electric Strike Access Control Kit including the AL900 Electric Strike.
Code: FC9043SS
A HOPPE SECUSAN Stainless Steel Euro Profile Escutcheon with an antibacterial, antimicrobial finish, to complement the Paris range of door furniture.